Fluke Corporation                                           MET/CAL Procedure
=============================================================================
INSTRUMENT:            Fluke 8062A: CAL ADJ /5720
DATE:                  13-Feb-95
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 1.1 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       83
CONFIGURATION:         Fluke 5720A
=============================================================================
#
# Source:
#   Fluke 8062A instruction manual (P/N 632695, March 1982, Rev. 2, 3/93)
#
# Compatibility:
#   MET/CAL 4.1 or later
#
# Subprocedures:
#   None
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5720A accuracy file contains 90 day specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
# The 90 day specifications of the 5720A are used in TUR computations.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                                                              W
  1.002  HEAD         EQUIPMENT SETUP
  1.003  DISP         [32]                   WARNING
  1.003  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.003  DISP         of this calibration. DEATH ON CONTACT may result if
  1.003  DISP         personnel fail to observe safety precautions.
  1.004  DISP         Ambient temperature: 21degC - 25degC.
  1.004  DISP         Relative humidity: less than 80%.
  1.004  DISP         Allow the UUT 30 min. to stabilize.
  1.004  DISP         NOTE: The top AC shield should remain installed on the
  1.004  DISP         instrument while the calibration adjustments are being
  1.004  DISP         performed. The positions of the trimpots and trimcaps
  1.004  DISP         are marked on the top AC shield along with a table
  1.004  DISP         summarizing the calibration procedures.
  1.005  DISP         The performance of the 8062B AC functions is affected
  1.005  DISP         by the capacitance between the main PCB and the bottom
  1.005  DISP         AC shield, which is dependent on the distance between
  1.005  DISP         them. The distance may vary, depending on whether the
  1.005  DISP         top cover is installed. To minimize performance
  1.005  DISP         variations, press down on the AC shield to simulate top
  1.005  DISP         cover installation while you perform the AC calibration.
  1.006  DISP         TURN ON UUT.
  1.007  HEAD         DC VOLTAGE ADJUSTMENT
  1.008  DISP         Connect the 5720A and the UUT as follows.
  1.008  DISP         [32] 5720A OUTPUT HI to UUT V Ohm S
  1.008  DISP         [32] 5720A OUTPUT LO to UUT COMMON
  1.009  DISP         Turn R6 fully clockwise (CW).
  1.009  DISP         Turn R5 fully counterclockwise (CCW).
  1.010  RNG          2V
  1.011  5720         1.9000V                                           S  2W
  1.012  DISP         Adj R6 (COARSE) for a reading between 1.9010 and 1.9025
  1.013  DISP         Adj R5 (FINE) for a UUT reading of 1.9000+/-0.0001V
  1.014  5720         *                                                 S
  1.015  RNG          200mV
  1.016  5720         190.0mV                                           S  2W
  1.017  DISP         Adjust R8 for a reading of 190.00+/-0.01mV
  1.018  5720         *                                                 S
  1.019  HEAD         AC VOLTAGE ADJUSTMENT
  1.020  DISP         Turn R18 fully clockwise (CW).
  1.020  DISP         Turn R15 fully counterclockwise (CCW).
  1.021  RNG          200mV                        AC
  1.022  5720         100.00mV                     200H                 S  2W
  1.023  DISP         Adj R15 (COARSE) for a reading between 100.40 and 100.95
  1.024  DISP         Adj R18 (FINE) for a UUT reading of 100.00+/-0.05mV
  1.025  5720         *                                                 S
  1.026  RNG          2V                           AC
  1.027  5720         1.0000V                      10kH                 S  2W
  1.028  DISP         Adjust C7 for a reading of 1.0000+/-0.0015V
  1.029  END